RCM Texband Cutter RTC-207-Tex-85

Fully equipped automatic cutting machine with driven film spool and dancer control for cutting Texbands for horizontal slat blinds. With the RCM marking system, a fold mark can be applied to the ends of the Texband. This model comes standard with a stacker that clamps up to 30 Texbands for easy removal.

Application

This fully equipped RCM Texband Cutter was developed to cut Huber Texbands for horizontal slats or venetian blinds to a constant uniform length and to mark both ends with a fold embossing for the subsequent sewing process. Processing of Texbands from other manufacturers on request. Due to the many standard options (full equipment), the machine is ideally suited for high productivity.

Texbands with a width of 6, 8 and 10 mm can be processed as standard. The fold mark can be set between 5 and 30 mm from the end or beginning of the Texband.

The sliver is transported by two synchronously driven, carbide-coated transport rollers (top and bottom), identical to the double drive with a 700 Ncm stepper motor.

The film spool is rotated by a motor when the Texband is pulled off. A dancer control, running on a linear guide, enables a very precise, even and jerk-free band take-off, even with a fast band advance. Tape feed speeds of up to 30 metres per minute can be processed.

During transport, the Texband is checked for thickness differences in the band by means of a tape defect control system, so that no Texbands with a seam connection can enter further processing. As soon as this thickened area is detected, the cutting machine stops production.

A stacker is fitted as standard to prevent the cut Texbands from flying to the floor. Up to 30 Texbands can be clamped in the stacker and thus easily removed.

All models have the special RCM marking system integrated, which ensures the exact position of the folding mark at the beginning and end of the Texband. This RCM marking system ensures that further processing and handling, such as sewing the bartack, is quick and easy.

This transverse marking with a slight bend in the tape means that the length accuracy from fold to fold can be maintained very precisely, even by less experienced personnel.

Work operations

37 Picto cutting texband lift tape38 Picto folding texband lift tape

Characteristics

  • Synchronously driven upper and lower transport rollers
  • Rollers with carbide coating
  • Transport speed adjustable; maximum tractive force of the drive motor 700NcmBand take-off via driven film spool with dancer control for very precise, smooth and jerk-free tape take-off
    Texband feed speeds up to 30 metres per minute
  • Integrated band error control system
  • Texbands with 6, 8 and 10 mm can be processed
  • Length and quantity can be set on the display
  • Length input in mm
  • Fast pneumatic scissors
  • Machine surface with feed unit, LxWxH: 60x40x60 cm
  • Total weight 30 kg with all options
  • Working pressure 6 bar
  • Power 230 Volt 60Hz

Features

Active pre-driver Texband

  • Roller dancer with sensor control for tension-free tape removal
  • Speed control with laser distance sensor, synchronous to basic machine
  • Driven film spool shaft by DC motor
  • Special driver for clamping the film spool
  • "TEXBAND"

RCM Marking-System for type LDM and LDMD

  • Fold for easy recognition of the loop bend point
  • Embossing distance front and back freely adjustable from 5 to 30 mm
  • Embossing unit can be switched on electronically

Stacker / clamping device for "TEXBAND"   

  • Clamping the cut Texbands into a bundle
  • Texband widths of 6, 8 and 10 mm can be processed with one setting
  • Stack quantity maximum 30 pieces; number of stacks freely adjustable from 1 to 30

Banderror control

  • Special sensor for measuring the differences in sliver thickness in 0.01 mm
  • Stopping of the band transport, manual cutting out of the defective area
  • There are two measuring states:
    good = one band runs through the control
    Error = either no band or two bands run through the error control

Your benefits

  • Low space requirement
  • Simple operation
  • High-quality components and processing of the machine
  • High quality output of the cut Texbands (upto 30 m per minute)
  • Driven film spool and dancer control ensure jerk-free band removal and thus high productivity
  • Integrated band error control system
  • Fixed stacker for bundling cut Texbands

Extensible options

Electronic automatic bartacker with direct drive type Brother
RTC-KE430

This automatic bartacker can be placed directly next to the Texband machine to ensure a continuous and smooth production flow.

The main features of this automatic bartacker are: 

  • Special thread cutter for short thread ends
  • Thread wiper; standard hook; staple lifter
  • Stitch rate maximum 3'200 stitches/minute
  • AC servo motor 550W (direct drive); single-phase 230V
  • LED sewing light integrated

You can get more details about this machine under this link: 
RCM Bartacker - KE-430


Barcode-Scanner for Texband Cutter RTC-207

Recurring jobs can be displayed as barcodes in an Excel file (included in the delivery). These barcodes can, for example, be printed out collectively on a sheet and placed at the machine. The barcode scanner is connected directly to the machine and thus recurring orders can be processed quickly and efficiently. The barcode scanner can be used with any Texband Cutter of the type RTC-207.

Jentschmann AG Schweiz

Feldstrasse 2
CH-8194 Hüntwangen
Telefon +41 44 735 83 83
Fax +41 44 735 83 84
This email address is being protected from spambots. You need JavaScript enabled to view it.

Jentschmann North America

66 Cambridge Cr.
Bradford, Ontario
L3Z 1E3 Canada
Dietmar Jeske
Phone +1 416 716 6117
This email address is being protected from spambots. You need JavaScript enabled to view it.